Qlogic QLogic Fibre Channel Switch Guide de l'utilisateur

Simplify059060-00 A Page iQLogic Fibre Channel SwitchEvent Message GuideFirmware Version 4.0

2 – Events and Event LoggingConfiguring Port Alarm Thresholds2-4 59060-00 0302.6Configuring Port Alarm ThresholdsYou can configure the switch to gene

59060-00 03 3-1Section 3Event MessagesThis section lists event messages from the command line interface and SANbox Manager in message ID sequence by

3 – Event MessagesAlarm Events3-2 59060-00 0303.1Alarm Events[A] [1003.0010] [Segmenting, zoneset zone_set_name not defined]Meaning: In non-interop m

3 – Event MessagesAlarm Events59060-00 03 3-30[A] [1003.0015] [Zoneset Activation received from switch with domain domain_ID failed, unknown zoneset

3 – Event MessagesAlarm Events3-4 59060-00 030[A] [1003.001F] [Failing remote zoning configuration, member limit for zone zone_name exceeded, (size=n

3 – Event MessagesAlarm Events59060-00 03 3-50[A] [1003.0041] [Zoning objects which contain Fibre Channel (FC) Address Members not being sent to remo

3 – Event MessagesAlarm Events3-6 59060-00 030[A] [1004.000C] [Eport Isolating due to Domain ID Locked, Domain ID unavailable]Meaning: An E_Port isol

3 – Event MessagesAlarm Events59060-00 03 3-70[A] [1004.0014] [Eport Isolating due to TOV Mismatch indicated on ELP]Meaning: An E_Port isolated becau

3 – Event MessagesAlarm Events3-8 59060-00 030[A] [1004.0029] [No Switch capable of being Principal Switch. Reconfigure Principal Switch Priority.]Me

3 – Event MessagesAlarm Events59060-00 03 3-90[A] [1004.0035] [Failed to connect to a switch due to incompatibility - check interop settings.]Meaning

Page ii 59060-00 A0ProductName ProductTypeUser’s Guide© 2000–2004 QLogic CorporationFirst Printed: April 2004All Rights Reserved Worldwide.Printed in

3 – Event MessagesAlarm Events3-10 59060-00 030[A] [1005.0024] [Switch must be reset after leaving the Diagnostics Admin State]Meaning: After changin

3 – Event MessagesCritical Events59060-00 03 3-1103.2Critical Events[C] [8100.0001] [LOG_MASK_NAME_SERVER] [Port: port_number] [Protocol violation fr

3 – Event MessagesCritical Events3-12 59060-00 030[C] [8400.000B] [Switch] [The switch will be shutdown several seconds]Meaning: The switch will be s

3 – Event MessagesCritical Events59060-00 03 3-130[C] [8400.002F] [Switch] [Zoning database of over 3000 zone members may damage certain non-QLogic s

3 – Event MessagesCritical Events3-14 59060-00 030[C] [8600.0015] [PortApp] [Port: port_number] [Unresponsive device device_al_pa on port port_number

3 – Event MessagesWarning Events59060-00 03 3-1503.3Warning Events[W] [8400.0007] [Switch] [Attempted unauthenticated login username account_name]Mea

3 – Event MessagesWarning Events3-16 59060-00 030[W] [8700.000A] [EPort] [Port: port_number] [No response from remote switch, resetting Inter-Switch

3 – Event MessagesInformative Events59060-00 03 3-1703.4Informative Events[I] [8200.0002] [mserver] [Port: port_number] [Rejecting request from addre

3 – Event MessagesInformative Events3-18 59060-00 030[I] [8300.0004] [zoning] [New Active ZoneSet zone_set_name]Meaning: A new zone set has been acti

3 – Event MessagesInformative Events59060-00 03 3-190[I] [8600.0006] [PortApp] [Port: port_number] [Online test passed, done = iterations_done, req =

59060-00 03 Page iiiTable of ContentsSection 1 Introduction1.1 Intended Audience ...

3 – Event MessagesInformative Events3-20 59060-00 030[I] [8F00.0009] From SANbox Manager: Link AddedMeaning: The application fabric discovery process

Page iv 59060-00 03ProductName ProductTypeUser’s Guide0Notes

59060-00 03 1-1Section 1IntroductionThis manual describes the alarm messages for the SANbox 3050 Fibre Channel switch using firmware version 4.0:This

1 – IntroductionTechnical Support1-2 59060-00 0301.3Technical SupportCustomers should contact their authorized maintenance provider for technical sup

59060-00 03 2-1Section 2Events and Event LoggingMessages originate from the switch or from the SANbox Manager application in response to events that

2 – Events and Event LoggingDisplaying the Events Using the Command Line Interface2-2 59060-00 0302.3Displaying the Events Using the Command Line Int

2 – Events and Event LoggingConfiguring the Event Log59060-00 03 2-302.4Configuring the Event LogYou can customize what events that are recorded in t