Qlogic QLA2000F Guide d'installation

Hardware Installation Guide for theQLA2000/2000F/2100/2100F/2102FFibre Channel Host Adapter Boardsfor the PCI BusFC0151102-00 DApril 16, 1999™Corp.

What You Need for Installation 2 – Hardware Installation2-2 FC0151102-00 DFigure 2-1. QLA2000 Board LayoutJ1ISP CHIPSERIAL NUMBERFigure 2-2. QLA2000F

2 – Hardware Installation What You Need for InstallationFC0151102-00 D 2-3Figure 2-3. QLA2100 Board LayoutJ1ISP CHIPSERIAL NUMBERFigure 2-4. QLA2100F

Power Supply 2 – Hardware Installation2-4 FC0151102-00 D2.3Power SupplyThe QLA2000/2100 boards supply +5 volts to pin 7 of the HSSDC copper interface

2 – Hardware Installation Installation in the ComputerFC0151102-00 D 2-54. Choose any PCI bus slot that supports bus mastering. Most motherboardsauto

Installation Help 2 – Hardware Installation2-6 FC0151102-00 DIf the information displayed on your monitor is correct (all installed devices arelisted

FC0151102-00 D 3-1Section 3Troubleshooting3.1Problems After InstallationThere are three basic types of installation problems that can cause your QLA2

System Configuration Problem Checklist 3 – Troubleshooting3-2 FC0151102-00 D3.3System Configuration Problem Checklist❑ Check the motherboard for prope

FC0151102-00 D A-1Appendix AFast!UTILA.1IntroductionThis appendix provides detailed configuration information for advanced users whowant to customize

Configuration Settings A – Fast!UTILA-2 FC0151102-00 D❑ Host Adapter BIOS. When this setting is disabled, the ROM BIOS on theQLA2xxx board is disable

A – Fast!UTIL Configuration SettingsFC0151102-00 D A-3A.2.4Raw NVRAM DataThis option displays the adapter’s NVRAM contents in hexadecimal format. Thi

QLogic CorporationPage ii FC0151102-00 DInformation furnished in this manual is believed to be accurate and reliable. However,QLogic Corporation assu

Configuration Settings A – Fast!UTILA-4 FC0151102-00 D❑ LUNs per Target. This setting specifies the number of LUNs per target.Multiple LUN support is

A – Fast!UTIL Scan Fibre Channel DevicesFC0151102-00 D A-5A.3Scan Fibre Channel DevicesThis option scans the FC loop and lists all the connected devi

Select Host Adapter A – Fast!UTILA-6 FC0151102-00 D

FC0151102-00 D B-1Appendix BSpecificationsTable B-1. QLA2xxx Board Operating EnvironmentEnvironment Minimum MaximumOperating temperature 0°C/32°F 55°C

B – SpecificationsB-2 FC0151102-00 DOnboard DMA Three independent DMA channels: two data and one command.Integrated 4K-byte frame buffer FIFO for eac

FC0151102-00 D Page iiiTable of ContentsQuick Installation Instructions vSection 1 Introduction1.1 General Description . . . . . . . . . . . . . .

Table of Contents QLA2000/2000F/2100/2100F/2102F Hardware Installation GuidePage iv FC0151102-00 DA.4 Fibre Disk Utility . . . . . . . . . . . . . .

FC0151102-00 D Page vQuick Installation InstructionsNOTE: The following QLogic host adapter boards are collectively referred to asthe QLA2xxx board u

Quick Installation Instructions QLA2000/2000F/2100/2100F/2102F Installation GuidePage vi FC0151102-00 D❑ Connect the appropriate Fibre Channel periph

FC0151102-00 D 1-1Section 1IntroductionNOTE: The following QLogic host adapter boards are collectively referred to asthe QLA2xxx board unless otherwi

Features 1 – Introduction1-2 FC0151102-00 D1.3Features❑ Compliance with Intel PCI version 2.1 specification❑ Compliance with Third Generation Fibre Ch

FC0151102-00 D 2-1Section 2Hardware Installation2.1Preinstallation ProceduresBefore installing your QLA2xxx board, take a moment to read this guide.C