Qlogic MPX200 Guide de l'utilisateur Page 169
- Page / 180
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3. Select the correct device, select the file hpux.cfi from the HPUX folder, and save it with a
new name.
4. Select the newly created boot option to boot from the new LUN.
vPar configurations
Pre Migration
• As the data migration must be done OFFLINE, shut down the system using the recommended
procedures to shutdown the vPars and system.
• Itanium servers require nPar mode for complete system shutdown.
Post Migration
• When bringing up the host, bring it up as single path boot volume and storage only. Once
the first boot is complete all the remaining paths to the storage can be enabled.
• To boot from the destination SAN disk, the disk must first be discovered. Follow the
recommended procedures for your system for a boot LUN discovery, select the LUN for the
booting, and boot the vPars.
vPar configurations 169
- Migration User Guide 1
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- Contents 7 7
- 1 Introduction 8
- 2 Getting started 10
- Data migration configuration 11
- 12 Getting started 12
- Supported configurations 13 13
- 14 Getting started 14
- Supported configurations 15 15
- Supported FC fabrics 16
- Supported storage arrays 16
- Hardware and software setup 17
- Software setup 18
- 3 Data migration objects 19
- Data migration job groups 20
- Data migration jobs 20
- Migration types 21
- Job scheduling 21
- Job states 22
- Job failover and failback 23
- VPG examples 24
- Presented targets 25
- 26 Data migration objects 26
- Global presentation 27
- Recommended steps 29
- Remote peers 30
- Online remote migration 30
- Online remote migration 31 31
- Data scrubbing 33
- Protection 34
- Users 35 35
- 4 Data migration licenses 36
- 38 Data migration licenses 38
- 40 Data migration licenses 40
- 5 Performing data migration 41
- Configuring the fabric 42
- Presenting LUNs to the MPX200 43
- 44 Performing data migration 44
- Rescanning Targets 45
- 46 Performing data migration 46
- 48 Performing data migration 48
- Mapping LUNs to initiators 49
- Mapping LUNs to hosts 50
- Using remote peers 51
- Importing a remote array 52
- Setting array properties 53
- 54 Performing data migration 54
- 56 Performing data migration 56
- 58 Performing data migration 58
- 60 Performing data migration 60
- 62 Performing data migration 62
- System Log 63
- Data migration job log 64
- 66 Performing data migration 66
- 68 Performing data migration 68
- Removing an offline array 69
- Creating and removing a DML 69
- 70 Performing data migration 70
- 72 Performing data migration 72
- 74 Performing data migration 74
- 6 Command line interface 76
- Command syntax 77
- Commands 77
- Commands 85 85
- 94 Command line interface 94
- Commands 95 95
- 96 Command line interface 96
- Commands 97 97
- 100 Command line interface 100
- Authority 101
- Keywords 101
- Examples 101
- 102 Command line interface 102
- 104 Command line interface 104
- 108 Command line interface 108
- Commands 109 109
- 112 Command line interface 112
- Commands 113 113
- Commands 117 117
- 118 Command line interface 118
- Commands 121 121
- 122 Command line interface 122
- 130 Command line interface 130
- 136 Command line interface 136
- Performance factors 139
- Maximizing performance 139
- Operational Behavior 140
- Best practices 141
- General precautions 142
- MSA2012fc Array Behavior 144
- 14. Reboot the MPX200 145
- 9 Restrictions 146
- Contacting HP 148
- Related information 148
- Prerequisites 149
- Typographic conventions 149
- Product feedback 150
- 11 Documentation feedback 151
- Linux multipath configuration 153
- HP-UX multipath configuration 156
- Pre-insertion requirements 162
- SNMP Parameters 164
- SNMP trap configuration 164
- Notifications 165
- 166 SNMP 166
- Notifications 167 167
- D HP-UX Boot volume migration 168
- PA-RISC systems 170
- Itanium Systems 170
- E Troubleshooting 171
- Glossary 174
- 176 Glossary 176
- 178 Index 178
- 180 Index 180
Produits connexes et manuels pour Logiciel Qlogic MPX200
Logiciel Qlogic MPX200 Spécifications
(60 pages)
(60 pages)
Logiciel Qlogic QLA2000F Guide de l'utilisateur
(281 pages)
(281 pages)
Logiciel Qlogic QLA2100F Spécifications
(243 pages)
(243 pages)
Logiciel Qlogic OFED+ Host Spécifications
(20 pages)
(20 pages)
Logiciel Qlogic QLA2102F Spécifications
(114 pages)
(114 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels