Qlogic QLogic 12000 Series Guide d'installation télécharger pdf (Page 23)

1–Installation

12800-040 Installation

D000140-001 D 1-13

Installation Tasks

1. Install the clip nuts. Install M6 clip nuts in the following locations on EIA rails:

Figure 1-8. Clip Nut Installation Locations

For improved stability, orient the clip nuts as shown (that is, orient the

flanges horizontally):

Figure 1-9. Clip Nut Orientation

2. Install support rails in the rack. Fasten with two (2) M6 screws per EIA rail to

pre-installed clip nuts and torque to 30 in-lb.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 133 134

QLogic 12000 Series 1
Document Revision History 2
Table of Contents 3
Hardware Installation Guide 4
Intended Audience 7
Documentation Conventions 7
cd /root and press ENTER 8
License Agreements 9
Technical Support 9
Knowledge Database 10
1 Installation 11
Cable Requirements 12
Uninterruptible Power Supply 14
Installation Tasks Checklist 15
Mark the Rack 16
12200/12300 Installation 17
1–Installation 18
1-8 D000140-001 D 18
D000140-001 D 1-9 19
Installation 20
Figure 1-6. 12200 Hat Rails 20
D000140-001 D 1-11 21
12800-040 Installation 22
Installation Tasks 23
1-14 D000140-001 D 24
D000140-001 D 1-15 25
12800-120 Installation 26
D000140-001 D 1-17 27
1-18 D000140-001 D 28
D000140-001 D 1-19 29
1-20 D000140-001 D 30
D000140-001 D 1-21 31
1-22 D000140-001 D 32
D000140-001 D 1-23 33
12800-180 Installation 34
D000140-001 D 1-25 35
1-26 D000140-001 D 36
D000140-001 D 1-27 37
1-28 D000140-001 D 38
D000140-001 D 1-29 39
1-30 D000140-001 D 40
D000140-001 D 1-31 41
12800-360 Installation 42
D000140-001 D 1-33 43
1-34 D000140-001 D 44
1-36 D000140-001 D 46
D000140-001 D 1-37 47
1-38 D000140-001 D 48
D000140-001 D 1-39 49
1-40 D000140-001 D 50
D000140-001 D 1-41 51
1-42 D000140-001 D 52
D000140-001 D 1-43 53
1-44 D000140-001 D 54
D000140-001 D 1-45 55
1-46 D000140-001 D 56
Connecting Power 57
Figure 1-41. DC ON/OFF Switch 58
Guidelines 59
User Site Installation 60
Start-up Procedures 61
1-52 D000140-001 D 62
D000140-001 D 1-53 63
1-54 D000140-001 D 64
Enabling 8X Ports 65
Figure 1-49. 8X Ports Enabled 66
D000140-001 D 1-57 67
1-58 D000140-001 D 68
Figure 1-52. 8X Ports Enabled 69
1-60 D000140-001 D 70
Component LEDs 71
Chassis Status and Attention 72
Fault Tolerant 72
Service Required 72
MRL Active 72
Figure 1-55. MRL Active LED 73
Leaf Module 74
Spine Module 75
SEEB Module 76
12200 and 12300 77
12800 Fans and Power Supplies 78
Power Supply LEDs 79
1-70 D000140-001 D 80
Procedures 81
1-72 D000140-001 D 82
D000140-001 D 1-73 83
1-74 D000140-001 D 84
D000140-001 D 1-75 85
1-76 D000140-001 D 86
D000140-001 D 1-77 87
QLogic 12000 Six-Port Upgrade 88
1-80 D000140-001 D 90
A QLogic 12000 Series 91
Environmental Specifications 92
Power Specifications 94
Power Distribution Guidelines 96
Table A-4. AC Plug Types 97
D000140-001 D A-9 99
12800 Series 100
A-10 D000140-001 D 100
B Safety and Regulatory 101
Safety Information 102
B-2 D000140-001 D 102
Statement 2: 103
B-4 D000140-001 D 104
ステートメント 2： 105
Statement 3: 106
Uttalande 3: 107
Kijelentés 3: 107
Инструкция 3: 107
ステートメント 3： 107
Statement 4: 108
D000140-001 D B-9 109
Statement 5: 110
Uttalande 5: 111
Kijelentés 5: 111
Инструкция 5: 111
ステートメント 5： 111
Statement 6: 112
Kijelentés 6: 113
Инструкция 6: 113
ステートメント 6： 113
Statement 7: 114
D000140-001 D B-15 115
ステートメント 7： 116
D000140-001 D B-17 117
B-18 D000140-001 D 118
C Serial Port Pinouts 119
Serial Port Pinouts 120
C-2 D000140-001 D 120
P5-Rx P5 P6-Tx 120
P6-Gnd P4 P4-Gnd 120
P4-Tx P3 P5-Rx 120
D000140-001 D C-3 121
C-4 D000140-001 D 122
D FRU Replacement 123
QLogic 12300 124
Fan/Power Supply Replacement 125
QLogic 12800 Series 126
Replacement Procedures 127
Power Supply Replacement 128
Leaf Module Replacement 129
Spine Module Replacement 131
Management Module Replacement 132

Commentaires sur ces manuels

Pas de commentaire

Qlogic QLogic 12000 Series Guide d'installation Page 23

Commentaires sur ces manuels

Produits connexes et manuels pour Commutateurs de réseau Qlogic QLogic 12000 Series