Qlogic QLogic 12000 Series Guide d'installation télécharger pdf (Page 22)

1–Installation

12200/12300 Installation

1-12 D000102-000 B

•M6 screws

Installation

1. Install the hat rails with mounting ears towards the port side of the switch. Fasten

with three (3) #6-32 screws per rail. Torque screws to 8in-lb.

Figure 1-10 12200 Hat Rails

2. Install six (6) cage nuts into the rack posts. Two cage nuts into posts on the

front side of the rack and four cage nuts into posts in the rear of the rack. Note

that the front of the rack is where the switch is installed.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 113 114

QLogic 12000 Series 1
Document Revision History 2
Table of Contents 3
Hardware Installation Guide 4
C Serial Port Pinouts 5
D FRU Replacement 5
Intended Audience 7
Documentation Conventions 7
License Agreements 8
Technical Support 10
4 D000102-000 B 10
1 Installation 11
Cable Requirements 12
Uninterruptible Power Supply 14
Installation Tasks Checklist 15
Mark the Rack 16
12200/12300 Installation 17
1–Installation 18
1-8 D000102-000 B 18
Installation 19
1-10 D000102-000 B 20
D000102-000 B 1-11 21
Figure 1-10 12200 Hat Rails 22
D000102-000 B 1-13 23
12800-180 Installation 24
D000102-000 B 1-15 25
1-16 D000102-000 B 26
D000102-000 B 1-17 27
Torque all screws to 30in-lb 28
D000102-000 B 1-19 29
Overview 30
Installation tasks 31
Assemble the Support Shelf 32
D000102-000 B 1-23 33
1-24 D000102-000 B 34
D000102-000 B 1-25 35
1-26 D000102-000 B 36
D000102-000 B 1-27 37
1-28 D000102-000 B 38
D000102-000 B 1-29 39
1-30 D000102-000 B 40
D000102-000 B 1-31 41
Connecting Power 42
Figure 1-29 DC ON/OFF Switch 43
Guidelines 44
User Site Installation 45
Start-up Procedures 46
D000102-000 B 1-37 47
D000102-000 B 1-39 49
1-40 D000102-000 B 50
Component LEDs 51
Chassis Status and Attention 52
Fault Tolerant 52
Service Required 52
MRL Active 53
Figure 1-37 MRL Active LED 53
Leaf Module 54
Spine Module 55
SEEB Module 56
12200 and 12300 57
12800 Fans and Power Supplies 58
Power Supply LEDs 59
1-50 D000102-000 B 60
Procedures 61
1-52 D000102-000 B 62
D000102-000 B 1-53 63
1-54 D000102-000 B 64
D000102-000 B 1-55 65
1-56 D000102-000 B 66
D000102-000 B 1-57 67
1-58 D000102-000 B 68
A QLogic 12000 Series 69
Environmental Specifications 70
12800 Series 71
Power Specifications 72
Power Distribution Guidelines 73
Table A-4. AC Plug Types 74
D000102-000 B A-7 75
A-8 D000102-000 B 76
B Safety and Regulatory 77
Safety Information 78
B-2 D000102-000 B 78
Statement 2: 79
B-4 D000102-000 B 80
ステートメント 2： 81
Statement 3: 82
Uttalande 3: 83
Kijelentés 3: 83
Инструкция 3: 83
ステートメント 3： 83
Statement 4: 84
D000102-000 B B-9 85
Statement 5: 86
Uttalande 5: 87
Kijelentés 5: 87
Инструкция 5: 87
ステートメント 5： 87
Statement 6: 88
Kijelentés 6: 89
Инструкция 6: 89
ステートメント 6： 89
Statement 7: 90
D000102-000 B B-15 91
ステートメント 7： 92
D000102-000 B B-17 93
B-18 D000102-000 B 94
C–Serial Port Pinouts 96
C-2 D000102-000 B 96
P5-Rx P5 P6-Tx 96
P6-Gnd P4 P4-Gnd 96
P4-Tx P3 P5-Rx 96
D000102-000 B C-3 97
C-4 D000102-000 B 98
QLogic 12300 100
Chassis Replacement 101
D–FRU Replacement 102
D-4 D000102-000 B 102
QLogic 12800 Series 103
Removal Procedures 104
Replacement Procedures 105
Power Supply Replacement 106
Leaf Module Replacement 107
Spine Module Replacement 109
Management Module Replacement 110
D000102-000 B D-13 111
D-14 D000102-000 B 112

Commentaires sur ces manuels

Pas de commentaire

Qlogic QLogic 12000 Series Guide d'installation Page 22

Commentaires sur ces manuels

Produits connexes et manuels pour Commutateurs de réseau Qlogic QLogic 12000 Series