Qlogic QLogic Fibre Channel Switch Guide d'installation Page 70
- Page / 206
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4 – Installation
Install Firmware
4-18 59055-00 B
D
4.2.8
Cable Devices to the Switch
Connect cables to the SFP transceivers and their corresponding devices, and
then energize the devices. Device host bus adapters can have SFP (or SFF)
transceivers or GigaBit Interface Converters (GBIC). LC-type duplex fiber optic
cable connectors are designed for SFP transceivers, while SC-type connectors
are designed for GBICs. Duplex cable connectors are keyed to ensure proper
orientation. Choose the fiber optic cable with the connector combination that
matches the device host bus adapter.
GL_Ports self configure as FL_Ports when connected to loop of public devices or
F_Ports when connected to a single device. G_Ports self configure as F_Ports
when connected to single public devices. Both GL_Ports and G_Ports self
configure as E_Ports when connected to another switch.
4.3
Install Firmware
The switch comes with current firmware installed. You can upgrade the firmware
from the management workstation as new firmware becomes available. Firmware
installation involves loading the firmware image file onto the switch, unpacking the
image file, and then resetting the switch to activate the new firmware.
Note: You can load and activate version 4.0.x firmware on an operating
switch without disrupting data traffic or riinitializing attached devices. If
you attempt to perform a non-disruptive activation without satisfying
the following conditions, the switch will perform a disruptive activation:
The current firmware version is 4.0.x version that precedes the
upgrade version.
No changes are being made to switches in the fabric including
powering up, powering down, disconnecting or connecting ISLs,
and switch configuration changes.
No port in the fabric is in the diagnostic state.
No zoning changes are being made in the fabric.
No changes are being made to attached devices including
powering up, powering down, disconnecting, connecting, and HBA
configuration changes.
Ports that are stable when the non-disruptive activation begins, then
change states, will be reset. When the non-disruptive activation is
complete, SANbox Manager sessions reconnect automatically.
However, Telnet sessions must be restarted manually.
- Installation Guide 1
- Document Revision History 2
- Table of Contents 3
- Section 3 Planning 4
- Section 4 Installation 4
- 59055-00 B Page v 5
- Appendix A Specifications 6
- Page viii 59055-00 B 8
- Introduction 9
- Related Materials 10
- Safety Notices 11
- Sicherheitshinweise 11
- Communications Statements 12
- Statement 12
- CE Statement 13
- VCCI Class A Statement 14
- Laser Safety Information 14
- Accessible Parts 15
- Pièces Accessibles 15
- Zugängliche Teile 15
- General Public License 16
- Preamble 16
- 1 – Introduction 17
- 59055-00 B 1-9 17
- 1-10 59055-00 B 18
- 59055-00 B 1-11 19
- 1-12 59055-00 B 20
- 59055-00 B 1-13 21
- 1-14 59055-00 B 22
- Technical Support 23
- Availability 23
- Training 23
- Contact Information 23
- 1-16 59055-00 B 24
- General Description 25
- Chassis Controls and LEDs 26
- Maintenance Button 26
- Resetting a Switch 27
- Chassis LEDs 28
- Input Power LED (Green) 28
- Heartbeat LED (Green) 28
- System Fault LED (Amber) 29
- Fibre Channel Ports 29
- Port LEDs 30
- Port Logged-In LED (Green) 30
- Port Activity LED (Green) 30
- Transceivers 31
- Port Types 31
- Ethernet Port 32
- Serial Port 33
- Power Supply and Fans 34
- Switch Management 34
- 2 – General Description 35
- 59055-00 B 2-11 35
- 2-12 59055-00 B 36
- Planning 37
- Device Access 38
- Soft Zones 39
- Performance 40
- Distance 40
- Bandwidth 41
- Port Licensing 42
- Multiple Chassis Fabrics 43
- Optimizing Device Performance 43
- 3 – Planning 44
- 3-8 59055-00 B 44
- Stacking 45
- 3-10 59055-00 B 46
- Common Topologies 47
- Cascade Topology 47
- Mesh Topology 48
- Multistage Topology 49
- Fabric Security 50
- User Account Security 50
- Fabric Services 51
- Fabric Management 51
- 3-16 59055-00 B 52
- Installation 53
- Environmental Conditions 54
- Installing a Switch 54
- Mount the Switch 55
- 4 – Installation 56
- 4-4 59055-00 B 56
- Install Transceivers 57
- 59055-00 B 4-7 59
- 4-8 59055-00 B 60
- Ethernet Connection 62
- Serial Connection 62
- 4-12 59055-00 B 64
- 4-14 59055-00 B 66
- Installation Disk 67
- Starting SANbox Manager 68
- Configure the Switch 69
- Cable Devices to the Switch 70
- Install Firmware 70
- 59055-00 B 4-19 71
- SANbox Login:admin 71
- Password: password 71
- 4-22 59055-00 B 74
- SANbox(admin) $>hotreset 74
- SANbox (admin) $>reset 74
- Powering Down a Switch 75
- 4-24 59055-00 B 76
- Diagnostics/Troubleshooting 77
- Heartbeat LED Blink Patterns 78
- System Error Blink Pattern 78
- POST Diagnostics 81
- 59055-00 B 5-5 81
- 2 seconds 81
- Logged-In LED Indications 82
- E_Port Isolation 83
- Excessive Port Errors 84
- 59055-00 B 5-9 85
- Chassis Diagnostics 86
- Recovering a Switch 87
- Maintenance – Exit 88
- Maintenance – Image Unpack 88
- Maintenance – Copy Log Files 89
- Maintenance – Reset Switch 90
- Specifications 91
- A – Specifications 92
- Fabric Specifications 92
- A-2 59055-00 B 92
- Maintainability 93
- Dimensions 94
- Electrical 94
- Environmental 95
- Regulatory Certifications 96
- Command Line Interface 97
- Modifying a Configuration 98
- Commands 101
- Admin Command 103
- Alias Command 104
- B – Command Line Interface 105
- 59055-00 B B-9 105
- Config Command 106
- 59055-00 B B-11 107
- B-12 59055-00 B 108
- Date Command 109
- Fallback Command 110
- Feature Command 111
- Hardreset Command 112
- Help Command 113
- History Command 114
- Hotreset Command 115
- Image Command 116
- Lip Command 117
- Passwd Command 118
- Ping Command 119
- Ps Command 120
- Quit Command 121
- Reset Command 122
- Set Command 127
- B-32 59055-00 B 128
- Set Config Command 129
- 10 Gbps Ports: G 130
- B-40 59055-00 B 136
- 59055-00 B B-41 137
- B-42 59055-00 B 138
- 59055-00 B B-43 139
- B-44 59055-00 B 140
- Set Log Command 141
- B-46 59055-00 B 142
- Stops logging of events 143
- Set Port Command 144
- Diagnostics 145
- Set Setup Command 146
- 59055-00 B B-53 149
- B-54 59055-00 B 150
- Show Command 151
- B-56 59055-00 B 152
- B-60 59055-00 B 156
- 59055-00 B B-61 157
- B-62 59055-00 B 158
- 59055-00 B B-63 159
- B-64 59055-00 B 160
- 59055-00 B B-65 161
- B-66 59055-00 B 162
- Show Config Command 163
- B-68 59055-00 B 164
- 59055-00 B B-69 165
- Show Log Command 166
- 59055-00 B B-71 167
- B-72 59055-00 B 168
- Show Perf Command 169
- B-74 59055-00 B 170
- 59055-00 B B-75 171
- Show Setup Command 172
- 59055-00 B B-77 173
- Shutdown Command 174
- Test Command 175
- Uptime Command 178
- User Command 179
- B-84 59055-00 B 180
- 59055-00 B B-85 181
- Whoami Command 182
- Zone Command 183
- B-88 59055-00 B 184
- 59055-00 B B-89 185
- B-90 59055-00 B 186
- Zoneset Command 187
- B-92 59055-00 B 188
- Zoning Command 189
- SANbox #> admin start 190
- 59055-00 B B-95 191
- B-96 59055-00 B 192
- 59055-00 B B-97 193
- B-98 59055-00 B 194
- Glossary 195
- Glossary-2 59055-00 B 196
- 59055-00 B Glossary-3 197
- Glossary-4 59055-00 B 198
- 59055-00 B Glossary-5 199
- Glossary-6 59055-00 B 200
- Numerics 201
- Index-2 59055-00 B 202
- 59055-00 B Index-3 203
- Index-4 59055-00 B 204
- 59055-00 B Index-5 205
- Index-6 59055-00 B 206
Produits connexes et manuels pour Commutateurs de réseau Qlogic QLogic Fibre Channel Switch
(12 pages)
(114 pages)Ace-backstage Super Stage Pocket manuály
Uživatelské manuály a uživatelské příručky pro Hardware Ace-backstage Super Stage Pocket.
Poskytujeme 1 manuály pdf Ace-backstage Super Stage Pocket ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels