Qlogic SANsurfer iSCSI HBA CLI Guide de l'utilisateur télécharger pdf (Page 71)

5 – Non-interactive Mode Commands

-vpd (Display VPD Information)

SN0054621-00 B 5-15

5.44

-csbootcode

(Clear Secondary Primary Target Information)

Type the following command to clear the secondary boot target and LUN:

-csbootcode <HBA No.>

5.45

-ver

(Display Program Version Information)

Type the following command to display the iSCSI HBA CLI program version

information:

-ver

5.46

-vpd

(Display VPD Information)

Type the following command to display VPD information:

-vpd <HBA No.>

1 2 ... 66 67 68 69 70 71 72 73 74 75 76 ... 79 80

User’s Guide 1
Page ii SN0054621-00 B 2
SN0054621-00 B Page iii 3
Table of Contents 5
Page vi SN0054621-00 B 6
SANsurfer iSCSI HBA CLI 7
SN0054621-00 B Page vii 7
Figure Page 8
Table Page 8
Introduction 9
1 – Introduction 10
Technical Support 10
1-2 SN0054621-00 B 10
Getting Started 11
Port Alias: 12
Non-interactive Mode 13
Initial Installation 15
Installation Instructions 17
SN0054621-00 B 3-3 17
3 – Initial Installation 17
3-4 SN0054621-00 B 18
SN0054621-00 B 3-5 19
Red Hat/SuSE Linux/PPC 20
Solaris SPARC/Solaris x86 20
Uninstall Instructions 20
3-8 SN0054621-00 B 22
Interactive Mode Commands 23
HBA Options Menu 24
HBA Network Settings Menu 25
Display Network Settings 25
Configure IP Settings 26
(Command Line Option -ipdhcp) 26
Using DHCP 26
Using SLP 27
(Command Line Option -isns) 27
HBA Firmware Settings Menu 27
(Command Line Option -c) 28
Change HBA Alias Name 36
Edit a Specific HBA Setting 37
Configure iSCSI Settings 37
(Command Line Option -n) 37
Configure Firmware Settings 38
Configure Device Settings 38
Configure Basic Settings 39
Configure Advanced Settings 40
Restore Default HBA Settings 40
(Command Line Option -rdf) 40
4 – Interactive Mode Commands 41
SN0054621-00 B 4-19 41
Display Bootcode Information 42
(Command Line Option -binfo) 42
Set Bootcode Mode 42
SN0054621-00 B 4-21 43
HBA Restore Factory Defaults 44
(Command Line Option -rdh) 44
HBA Information 44
(Command Line Option -pinfo) 44
Reset HBA 45
(Command Line Option -b) 45
Target Menu 46
List Targets 46
(Command Line Option -t) 46
Bind Target 47
(Command Line Option -pb) 47
Unbind Target 47
Configure Target Parameters 47
Add a Target 48
(Command Line Option -pa) 48
Add a CHAP Entry 50
Add a Default BIDI CHAP 50
Edit a CHAP Entry 51
(Command Line Option -edchap) 51
Delete a CHAP Entry 51
List LUN Information 52
(Command Line Option -l) 52
Diagnostic Menu 52
Ping Target 53
(Command Line Option -ping) 53
Perform Loopback Test 53
(Command Line Option -lb) 53
(Command Line Option -rwt) 54
Display HBA Statistics 54
(Command Line Option -stat) 54
SN0054621-00 B 4-33 55
(Command Line Option -vpd) 56
Set Working Adapter 56
Non-interactive Mode Commands 57
■ Host name 59
■ Host version 59
■ Host type 59
(Configure iSCSI Settings) 60
(Perform Loopback Test) 63
-dspchap 64
(Display a CHAP Table) 64
-chapmap 64
(Restore HBA Settings) 67
5-16 SN0054621-00 B 72
Index-8 SN0054621-00 B 80

Commentaires sur ces manuels

Pas de commentaire

Qlogic SANsurfer iSCSI HBA CLI Guide de l'utilisateur Page 71

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau Qlogic SANsurfer iSCSI HBA CLI